At the R/W end it's either up or down!!

The Crewroom for non-FS related stuff, fun and general chat.

Moderators: Guru's, The Ministry

User avatar
airboatr
Red Arrows
Red Arrows
Posts: 6775
Joined: 25 Oct 2007, 07:17

Re: At the R/W end it's either up or down!!

Post by airboatr »

Thank Nigel I like that sort of stuff
:dancer:
a few more jaw droppers
http://www.alexisparkinn.com/photogalle ... ontest.wmv

and who says you need floats to make a water landing
http://www.alexisparkinn.com/photogalle ... anding.wmv

SkippyBing
Concorde
Concorde
Posts: 1459
Joined: 30 Aug 2006, 18:21

Re: At the R/W end it's either up or down!!

Post by SkippyBing »

Aww no, I was actually in the NL Antilles in August. Okay we went to Curacao (top run ashore by the way) to think we could have manufactured an excuse to go to that little runway as well!!
Image

User avatar
Nigel H-J
Red Arrows
Red Arrows
Posts: 8035
Joined: 14 May 2005, 15:33
Location: Lincolnshire

Re: At the R/W end it's either up or down!!

Post by Nigel H-J »

Crikey John, that looked a bit of a hairy landing.....!! :o

Nigel.
I used to be an optimist but with age I am now a grumpy old pessimist.

Quixoticish
Concorde
Concorde
Posts: 1124
Joined: 15 Oct 2005, 15:16
Location: York

Re: At the R/W end it's either up or down!!

Post by Quixoticish »

Nigel H-J wrote: Chris, the T/O is somewhere on You Tube but cannot link it until tomorrow unless some-one can find it before then.
I'd be intrigued to see it, no doubt it's as equally impressive as the landing!

User avatar
Nigel H-J
Red Arrows
Red Arrows
Posts: 8035
Joined: 14 May 2005, 15:33
Location: Lincolnshire

Re: At the R/W end it's either up or down!!

Post by Nigel H-J »

Hi Chris

Think this is the same airport though the take-off isn't as good as the landing simply because the co-pilot was not filming it. Far too busy the both of them to ensure they got airborne before reaching the end of the runway!!

http://uk.youtube.com/watch?v=xHnwIdgFjRk

Nigel.
I used to be an optimist but with age I am now a grumpy old pessimist.

Quixoticish
Concorde
Concorde
Posts: 1124
Joined: 15 Oct 2005, 15:16
Location: York

Re: At the R/W end it's either up or down!!

Post by Quixoticish »

Nigel H-J wrote:Hi Chris

Think this is the same airport though the take-off isn't as good as the landing simply because the co-pilot was not filming it. Far too busy the both of them to ensure they got airborne before reaching the end of the runway!!

http://uk.youtube.com/watch?v=xHnwIdgFjRk

Nigel.
Sorry Nigel, I think we've got our wires crossed. I was talking about wanting to see a take-off from the greasy speck of mud that the Otter lands on in the clip John posted as opposed to the original post. As short as the runway is in the original video I can actually comprehend a take-off from there with a good stiff breeze; where as the video John posted.... I can't see it flying out on it's own. :o

http://uk.youtube.com/watch?v=_8wmZ6hhpg8

User avatar
Chris Trott
Vintage Pair
Vintage Pair
Posts: 2591
Joined: 26 Jun 2004, 05:16
Location: Houston, Texas, USA
Contact:

Re: At the R/W end it's either up or down!!

Post by Chris Trott »

SkippyBing wrote:Does anyone know where that is? It'd be interesting to try it in FS.
Well, I have SABA 2004 (by coincidence actually, never actually flown in) and so I tried it this afternoon. Sadly, it took me 3 tries to get the right approach path to land on the numbers and stop in time. The other times I either came in too shallow or too steep and because there's no glidepath guidance and it's an elevated runway, it's definitely tricky. I'm sure in the real world they have a written approach procedure for whatever airline operates into the airport that makes it much simpler. Once you get it right though, it's quite fun actually.

BTW, I used the Project TWOTTER DHC-6 which has by-far the best Twin Otter flight dynamics out there even if their manual uses RPMs for the props (when the gauges are %) and % N1 for power when it's only got a torque gauge (and this is using the included DHC-6 panel for the plane, not a 3rd party one). :lol:

Post Reply