Page 2 of 4
Re: A2A T6 KF729 (G-BJST) wip
Posted: 05 Apr 2016, 20:16
by DaveG
Cheers Dave.
BTW, if anybody wants it, I've knocked up a little gauge that lets you pre-set the various canopy, spinner and ADF aerial options on a per-aircraft basis so you don't have to configure it in-sim each time.
Re: A2A T6 KF729 (G-BJST) wip
Posted: 05 Apr 2016, 20:17
by DaveB
This look ok Dave??
Works for me. I've downloaded a couple already and deleted them when I had a close look
This is a definite keeper
ATB
DaveB
Re: A2A T6 KF729 (G-BJST) wip
Posted: 05 Apr 2016, 20:28
by DaveG
I don't think that looks too bad. Maybe a bit too grey, and not silvery enough though.
I hate silver paint.
I'm not 100% happy with the font for the reg, but it's not too far off.
The fin markings seems to stretch oddly from some angles, but there's nowt I can do about that.
A lot of the other paint's I've downloaded so far are too shiny for my taste, so I've tweaked those a bit as well.
Re: A2A T6 KF729 (G-BJST) wip
Posted: 05 Apr 2016, 20:34
by DaveB
Duff fonts have been doing my head in. You can't pay £35 for a model and put crap paints on it
Silver
is a swine. This one works for me though. You can make it more silver for FSX (if possible) or leave as-is. I'm happy to have a 'normal'.. boring Brit paint
ATB
DaveB
Re: A2A T6 KF729 (G-BJST) wip
Posted: 05 Apr 2016, 23:06
by T6flyer
Looks fine to me. Shouldn't the serial number be under both wings?
Martin
Re: A2A T6 KF729 (G-BJST) wip
Posted: 06 Apr 2016, 07:05
by DaveG
Not according the photos I've based it off, all show it only under one wing.
I'm going to experiment a bit more with the colour tonight if I get time.
Re: A2A T6 KF729 (G-BJST) wip
Posted: 06 Apr 2016, 10:09
by T6flyer
DaveG wrote:Not according the photos I've based it off, all show it only under one wing.
I'm going to experiment a bit more with the colour tonight if I get time.
Whoops...sorry. And I've been under those very wings lots of times!
Martin
Re: A2A T6 KF729 (G-BJST) wip
Posted: 06 Apr 2016, 11:16
by JohnWillimas
DaveG wrote:Cheers Dave.
BTW, if anybody wants it, I've knocked up a little gauge that lets you pre-set the various canopy, spinner and ADF aerial options on a per-aircraft basis so you don't have to configure it in-sim each time.
Yes please Dave, that would be handy...
Re: A2A T6 KF729 (G-BJST) wip
Posted: 06 Apr 2016, 19:36
by DaveG
Here you go John (and anyone else who wants it)
http://daveg.cbfsim.org/files/T6_Config_gauge.zip
The ReadMe should explain everything, but just shout if there's any problems.
Re: A2A T6 KF729 (G-BJST) wip
Posted: 06 Apr 2016, 20:03
by DaveB
Cheers Dave
EDIT: BTW.. I took a look at the MV F-4. There are at least 11 maps per paint
I don't have the get up and go I'm afraid. Damn shame as there are a few I'd like to do. Think I'll stick with JY's AI model
ATB
DaveB