Classic British Flight Sim

Well they have 14 cylinders and a max of 2700 RPM but I've just seen mention of a reduction ratio of 1.8...So I guess it must have a gearbox :think:

Hi Peter

The original starting post reffered to the whole engine :k:

I know it's a fix block.I meant the whole interal revoling part like the crankshaft as opposed to the very front via a gear.

Bristol Hercules for instance revolved the opposite way to Merlins



Garry

Hi Peter you got in while I was posting.

Thank for finding that out.

Garry

Normally aircraft that had counter rotating props, the counter rotating engine is a mirror image of the standard normal rotating engine.

While there were vast numbers of R-1820 and R-1830 engines made, only a limited number of them would be counter rotating. Even if some DC-3's came out of the factory with counter rotating engines its likely that over time a standard engine would replace the counter rotating engine as replacement engines and replacement parts are more plentiful for them.

An other possibility if no DC-3's came out of the factory that way that someone could have installed a counter rotating prop/engine as the mounts would all be the same.

Someone at M$ must have seen one in that configuration for them to go though the effort to change there model between versions. But if peter has not seen one they must be very rare.

Here is a sectioned one:-



I think there is a "Sun & Planet" type reduction gear at the right end (Propeller) :think:

It is a Pratt & Whitney Twin Wasp...double row 14 cylinder radial.

petermcleland wrote:

Kevin Farnell wrote:

petermcleland wrote:Just another bug I guess...I don't think there ever was one with contra-rotating props :think:

'Contra-rotating' and counter-rotating' are two totally different engineering designs. The first, being two props in tandem' turning in opposite directions . The second, props on differnet engines, turning in opposite dirctions.

Yes indeed...I should have said counter-rotating

And I should have said 'different' not 'differnet' :doho:

We all make mistakes.

Regards

Kevin

All P&W radials of more than 1000HP have reduction gears. Most of the engines below this do as well, but it's not absolute. The reason for this is mainly to reduce torque at the propeller shaft. One of the biggest problems with radials is their prodigeous torque. By installing reduction gears, it allows for more manageable torque levels to be exerted upon the shaft. This is the biggest reason for the problems that were encoutered with the R4360 and R3350 and the advent of some of the very sophistocated reduction gearing present on them.

Also, the entire engine operates either clockwise or counter clockwise, the reduction gear only changes the input and output RPMs. To place a reversing gear on the output shaft to swap the direction of the prop would add weight to one side of the aircraft that could not be matched correctly on the other side, so it's simply easier to build engines that turn one way or the other. This is the reason you don't find many aircraft (civilian or military) with counter rotating engines. It's extremely expensive to have to maintain two separate spares stores when you have two engines that externally are identical but have different cam shafts, accessories, reduction gears, governors, and propellers. With aircraft as big as the DC-3, there is enough moment on the aircraft to counter any adverse torque presented by both engines operating in the same direction.

That makes sense Chris

Imaging a port engine failure and all the spares in the hangar are Starboards.

The only civilian airliner that I can think of off hand with counter rotating was the Jetstream 41

There may well be other turbo props but TBH I've not looked.

Having said that the J41 gave itself away by being different so it may be unique on the types I've seen myself or I may have noticed.

A few light twins seemd to have them

Garry

Most of the Cessna Twins have counter-rotating engines. It was done to allow as small a wing and tail as possible to fit inside what was then the "standard" T-Hangar size in the US. That T-Hangar was not much larger than a Cub or Cessna 140. Seems to have worked at least a little bit since Cessna sold more light twins than any other manufacturer.

Actually, I realise now that big radials would have to have a reduction gear to prevent the propeller tips from going supersonic...Which they did anyway on the Harvard. The Twin Wasp with an engine RPM of 2700 would need to reduce that by about half to keep the propeller subsonic