BETA testers for my HENDY 302 please
Moderators: Guru's, The Ministry
-
- Vintage Pair
- Posts: 2580
- Joined: 10 Jul 2009, 08:33
- Location: Chacombe about 2 mile east of M40 J11
Re: BETA testers for my HENDY 302 please
OOOPs!
Keith
Keith
Re: BETA testers for my HENDY 302 please
Maybe it belongs to Peter Watkins. Poor Peter. This one off aircraft is really going to limit his repaint possibilities.
Brian
Brian
-
- Vintage Pair
- Posts: 2580
- Joined: 10 Jul 2009, 08:33
- Location: Chacombe about 2 mile east of M40 J11
Re: BETA testers for my HENDY 302 please
But maybe my next will test his B+W colour interpretation to the limit- there were 22 of them built, but with 3 different engine types; Gipsy Majors, Napier Javellins & Cirrus Hermes IV, in fact a logical development of the Hendy - the D type Percival Gull.
Keith
Keith
Re: BETA testers for my HENDY 302 please
That'll keep him busy. Can't wait to see the Gull.
Brian
Brian
Re: BETA testers for my HENDY 302 please
Just a few points : ( FS9 used )
1. I find it impossible to see the compass either in normal view or in virtual cockpit
2.The spinning behaviour is curious : I found that it would spin fairly consistently provided near full throttle was maintained, but the moment the throttle is shut, it falls out of the spin into a straight dive . If a spin is attempted with ( as it should be ) the throttle shut, it goes through about 90 degs of a spin and then adopts a straight stalled attitude . I was not able to demonstrate wing drop off a climbing turn in either direction
3.I found that with power on , it was possible to land it in a 3 point attitude at negligible IAS ( less than 20mph ) provided the stall was only initiated very close to the ground
An interesting little aeroplane
1. I find it impossible to see the compass either in normal view or in virtual cockpit
2.The spinning behaviour is curious : I found that it would spin fairly consistently provided near full throttle was maintained, but the moment the throttle is shut, it falls out of the spin into a straight dive . If a spin is attempted with ( as it should be ) the throttle shut, it goes through about 90 degs of a spin and then adopts a straight stalled attitude . I was not able to demonstrate wing drop off a climbing turn in either direction
3.I found that with power on , it was possible to land it in a 3 point attitude at negligible IAS ( less than 20mph ) provided the stall was only initiated very close to the ground
An interesting little aeroplane
-
- Vintage Pair
- Posts: 2580
- Joined: 10 Jul 2009, 08:33
- Location: Chacombe about 2 mile east of M40 J11
Re: BETA testers for my HENDY 302 please
Compass position - difficult to see because of the 'fixed' eye point in FS9 & FSX, but in a real aircraft, Proctor for example, its easy to adjust & to see, 'cos one can bend forward & from side to side. I have given a pop-up on the Compass card/Icon.
Spinning, I do it power off, but do not initiate until below 30 mph in a very high AoA attitude, just needs full rudder. One does though have to be quick on the opposite rudder as one can then enter a spin in the other direction.
Not tried a power on stall.....interesting, or dropping a wing in a climbing turn!
Thank you for your feedback. BTW what frame rate are you set for, & did you get any 'square wheel'/bounce problem?
Keith
Spinning, I do it power off, but do not initiate until below 30 mph in a very high AoA attitude, just needs full rudder. One does though have to be quick on the opposite rudder as one can then enter a spin in the other direction.
Not tried a power on stall.....interesting, or dropping a wing in a climbing turn!
Thank you for your feedback. BTW what frame rate are you set for, & did you get any 'square wheel'/bounce problem?
Keith
Re: BETA testers for my HENDY 302 please
Keith. Frame rate limited to 42, and I noticed no great diminution below this even though my system is now pretty primitive. I'm afraid my stalls off climbing turns came from my past ..when I was an FI ( predominantly on Cessnas ) our CFI had a fetish for such stalls - and insisted we always taught them because they taught the student a good deal about control because it was impossible to predict which wing would drop. Usually it was the outer wing in the turn , but perhaps 1 in 4 would drop the inner wing with more dramatic consequences. Because this was much less predictable than with a spin , recovery from this taught students more and gave them more confidence that they could cope with anything the aeroplane threw at them
I did get one feeling of "square wheels" on a very low speed landing !
Thanks for a lovely little craft
I did get one feeling of "square wheels" on a very low speed landing !
Thanks for a lovely little craft
- blanston12
- Vintage Pair
- Posts: 2785
- Joined: 28 Jun 2004, 20:45
- Location: San Francsico, California
Re: BETA testers for my HENDY 302 please
I realize that this is an FS9 model and the reflectiveness issues in P3D is outside the scope of the project, but as a lesson in repainting, how would I add that to the textures
Joe Cusick,
I am serious, and don't call me Shirley.
I am serious, and don't call me Shirley.
-
- Vintage Pair
- Posts: 2580
- Joined: 10 Jul 2009, 08:33
- Location: Chacombe about 2 mile east of M40 J11
Re: BETA testers for my HENDY 302 please
Joe, Yes if anyone can help on that matter I would be happy to participate, but will need someone who can test in P3D.
BTW - following all comments from here & elsewhere I am attempting to revise the FDE so that stable stalls & spins over the large C of G range can be accomplished - might have to fiddle the C of G? Will keep you posted when I find the golden rivet!!! It seems to be a difficult aircraft - not had this much trouble before & Airwrench no real help either!
Keith
BTW - following all comments from here & elsewhere I am attempting to revise the FDE so that stable stalls & spins over the large C of G range can be accomplished - might have to fiddle the C of G? Will keep you posted when I find the golden rivet!!! It seems to be a difficult aircraft - not had this much trouble before & Airwrench no real help either!
Keith
Re: BETA testers for my HENDY 302 please
Out of curiosity, how are you setting the dynamics to simulate spinning - given the limitations of FS9 ?
Might this be what is giving you headaches in the flight dynamics?
Might this be what is giving you headaches in the flight dynamics?