HS748 start problems

[TSR2]

Hi Tony,

I'll try and put something together over the next few days, work permitting. What OS are you running? I'm just following the startup process from the checklist in the 2D panel.

[TSR2]

Just another thought, if you manage to get engine failure after 20minutes im guessing you haven't switched in the correct level of deicing (fast above -6, slow below -6 - that's from memory, but its slow the colder it gets) or you're cooking the engines.

[Viscount Cornbank]

Sounds to me as though you may have either the FS9 cab or aircraft cfg installed rather than the FSX one. They each require different starter coding and won't work properly in the wrong simulator. The FS9 pack has three panel variations; 2A, 2B and 2C, while the FSX pack has only 2A and 2B. Check the panel cfg in the [VCockpit01] section; if this line is present it is the FS9 version:

gauge07=HS748!Engine_Systems_Process_HS7,1005,0,1,1

The FSX version should read:

gauge07=HS748!Engine_Systems_Process_HS7_FSX,1005,0,1,1

cheers

Fraser

[TSR2]

Thanks Fraser

[Vc Ten]

Been flying her about for a few days in fsx and either engine will restart ok in the sim You have to go into the 2d panel initially to "start" the electrics but after that its fine Make sure the fuel trim is set to at least 50% It used to default to zero and caught me out lots of times But I think Frazer must have altered it in the updated panel as it now defaults to 100% The only time it wouldnt start was when i forgot to press the start button As Fraser said make sure you are running the correct version for fsx
ATB
Dale

[J0hn]

I used to have this problem all the time - it would start up just fine from cold, but refused flat when warm. Most I could get was one engine to start - the other just flat refused.

That's why I could never fly this for long in Air Hauler

I currently have the 780 (Andover) installed, I don't know if that is the same panel config, but it doesn't have any line for engine starting (I had the same issue with it). Unfortunately I can't access my HS748 panel files, as it is in USB Hangar Storage and that's playing silly beggars.

I do have the last panel update, though, and that does have the FSX engine starting line - so when I manage to get into my storage drive, I'll give it a test. I'll be chuffed if the warm start problems are fixed

I remember we had a rather lengthy discussion about this a few years back.

[migman29]

I'm on Fs9,but I've shut down,left it for five mins and then re-started it all from the VC with no problems.

If you need,I'll document the procedure I've always used(been using this thing from the early days of Rick doing it),
it's pretty automatic for me now,but it always starts hot or cold.

[TSR2]

Hi guys,

Just to be clear, there is a different CAB file for the gauges in FSX and FS9. If someone is using the FS9 CAB file in FSX it wont work, in a way very similar to what Tony is describing, hence Fraser's post. I suspect Tony is following the procedure but using the FS9 CAB file.

[tonyc]

Fraser

Something is definitely wrong here I just looked at my Panel cfg and this is what VC Cockpit01 looks like:

[Vcockpit01]
file=panel_overhead748.bmp
file_1024=panel_overhead748.bmp
Background_color=0,0,0
size_mm=1024,1024
visible=0
pixel_size=1024,1024
texture=$overhead748

gauge00=HS7!Overhead_Port_VC, 4,321,391,697
gauge01=HS7!Overhead_Stbd, 629,321,391,697
gauge02=HS7!Avionics, 396,321,232,697
gauge03=HS7!Data_Card, 3,136,97,145
gauge04=HS7!Magnetic_compass_VC, 2,4,127,128
gauge05=HS7!Pressure_Controller, 133,4,150,98

Its totally different and no Gauge 07 it only goes up to 05!

Regards

Tony

[TSR2]

I'd suggest you delete the version you have installed and download the version from our library, and the latest panel update from Fraser, making sure you download the FSX version. There are some other sites that have the FS9 version badged as FSX compatible.